Online · on your design · nothing built, nothing uploaded

Will it power up,
or will it burn?

Drop your KiCad board and we power it up virtually, before you spend anything on fabrication: shorts, the power budget, regulators and their feedback dividers, every rating, input protection, high-voltage spacing, reset and boot pins, logic levels between chips, and the current flowing through every track and via. It runs entirely in your browser.

Your board

.kicad_pcb or a zipped KiCad project

Result

The result appears here: every check, what failed and where, and what to change.

What the test does

32 checks from every angle, the way an engineer powers up a prototype.

Each check reads the board itself: nets, pads, the parts and their values, the pin names and types KiCad carries over from the schematic, and the copper.

Shorts and connections
  • Copper shorts between power nets. Every piece of copper of every power net against every other: a supply touching ground or another rail.
  • Power and ground reach every pin. Union-find over pads, tracks, vias and pours: supply and ground pins cut off from their rail.
  • Parts that tie two rails together. 0 Ω resistors, jumpers, fuses and ferrites between a supply and ground, or between two voltages.
  • Supply and ground pins left unconnected. Supply and ground pins of chips, by their schematic pin type, that are not connected or alone on a net.
  • Separate grounds that never meet. Ground nets (GND, AGND, PGND...) joined through net ties and 0 Ω parts: any that never meet the main ground.
  • Power copper that touches no pin. Tracks and pours on power nets that touch no pad.
Sources and power budget
  • Every rail has one source. Every rail fed by a connector, battery or regulator; two regulator outputs on one rail.
  • Power budget against each source. Rail currents traced back through every regulator (linear: equal current; switching: by power) to each input, against USB limits and regulator ratings.
  • Regulator enable pins. Enable pins tied to ground (rail never comes up) or left floating.
  • Output voltage set by the feedback divider. The output voltage an adjustable regulator is set to by its feedback resistors, against the rail it feeds.
Regulators and converters
  • Regulators: input, output and heat. Input maximum, wrong output rail, swapped input and output, headroom, and junction temperature of linear regulators from (Vin − Vout) × I × θJA.
  • Regulator input and output capacitors. Capacitance near each regulator's input and output against its datasheet minimum.
  • Converter inductor current rating. Converter inductor saturation current against the load current plus ripple margin.
Component ratings
  • Chips within their supply limits. Known chips against their recommended and absolute-maximum supply voltage.
  • Capacitor voltage ratings. Voltage across each capacitor against its rating, with derating for tantalum.
  • Polarised capacitor orientation. Electrolytic and tantalum capacitors with + on the lower voltage.
  • Resistor power dissipation. V² / R for resistors across rails against the package rating.
  • Diodes and LEDs across rails. LEDs with no series resistor, protection diodes the wrong way round, zeners below their rail.
  • Diodes in the power path. Series diodes between rails: current rating, and forward drop × current against what the package can shed.
  • Fuse ratings against the current. Fuse and PTC ratings against the current of the rail behind them.
Protection and safety
  • Reverse-polarity protection on inputs. Inputs from a jack, terminal or battery that reach chips with no series diode, MOSFET or ideal-diode controller.
  • Surge and ESD protection on inputs. A TVS diode or varistor on every power input.
  • Overcurrent protection on inputs. A fuse, PTC or eFuse on every power input.
  • Spacing between nets at different voltages (IPC-2221B). Copper gap between nets at different voltages against IPC-2221B Table 6-1.
  • USB VBUS capacitance at plug-in. Capacitance on VBUS against the 10 µF USB allows at plug-in.
Startup and boot
  • Reset and enable pins of chips. Reset and enable pins of chips tied to ground, floating, or without a pull-up.
  • Boot mode pins. BOOT0 of STM32 and GPIO0 of ESP32 in a state that skips your firmware.
  • Decoupling at supply pins. A capacitor from each supply pin of each chip to ground, within 10 mm.
Signals between voltage domains
  • Signals crossing voltage domains. Signals between chips on different supply voltages with no level shifter.
  • Pull-ups to the wrong rail. Pull-up resistors to a rail higher than the chips on the signal.
Copper and heat
  • Track and via heating at the rail current. DC nodal analysis of each rail's copper (conjugate gradient): current and IPC-2221 temperature rise in every track and via.
  • Voltage drop to each load. The voltage left at every load after the copper of the rail.

Limits of an online test: it cannot run firmware, see parts that are not on the board, or check a part it does not know against its datasheet; those are named in the result rather than guessed. Rails without a known voltage or current are listed so you can set them.

Add it to your order

An engineer behind every finding.

Add the power-on test to a routing order or a design project and your engineer runs it on your board and on every board we deliver, fixes what belongs to the design or the routing, checks what software cannot, and signs it off.

$95 per order
  • Every finding of the online power-on test reviewed and resolved
  • Rail voltages and currents confirmed against your requirements
  • Input protection: reverse polarity, over-voltage and ESD on power entry
  • Fusing, inrush and hot-plug behaviour
  • Regulator and power-device dissipation at the real load
  • Power sequencing and reset behaviour of processors and FPGAs
  • Parts the test does not know checked against their datasheets
  • Safe first power-up procedure written for this board
FAQ

Questions about the power-on test

Is my board uploaded?

No. The free test runs in your browser; the file never leaves your computer. With an order, the same test runs on our portal on the files you send us.

Where do the rail voltages come from?

From the net names designers use (+3V3, 5V, VBUS, V1P8...) and from the fixed output of recognised regulators. Anything else is listed so you can type it in; the test runs again instantly.

Does a pass mean the board works?

It means none of the problems that destroy a board at first power-up were found in the design. It does not test firmware or every function of the product, and it names what it could not check.

Which files work?

KiCad 6 to 9 boards (.kicad_pcb) on their own or in a ZIP of the project. Pin names and types come from KiCad 6 and later.